...
| Section |
|---|
| Column |
|---|
| | Name | Pin # | Name | Anchor |
|---|
| tab_nucleoCN7 |
|---|
| tab_nucleoCN7 |
|---|
|
|
|---|
| PC10 | 1 | 2 | PC11 |
|---|
| PC12 | 3 | 4 | PD2 |
|---|
| VDD | 5 | 6 | E5V |
|---|
| BOOT0 | 7 | 8 | GND |
|---|
| NC | 9 | 10 | NC |
|---|
| NC | 11 | 12 | IOREF |
|---|
| PA13 | 13 | 14 | RESET |
|---|
| PA14 | 15 | 16 | +3V3 |
|---|
| PA15 | 17 | 18 | +5V |
|---|
| GND | 19 | 20 | GND |
|---|
| PB7 | 21 | 22 | GND |
|---|
| PC13 | 23 | 24 | VIN |
|---|
| PC14 | 25 | 26 | NC |
|---|
| PC15 | 27 | 28 | PA0 |
|---|
| PH0 | 29 | 30 | PA1 |
|---|
| PH1 | 31 | 32 | PA4 |
|---|
| VLCD | 33 | 34 | PB0 |
|---|
| PC2 | 35 | 36 | PC1 |
|---|
| PC3 | 37 | 38 | PC0 |
|---|
Table 10: NUCLEO-L053R8 CN7 header. |
| Column |
|---|
| | Name | Pin # | Name | Anchor |
|---|
| tab_nucleoCN10 |
|---|
| tab_nucleoCN10 |
|---|
|
|
|---|
| PC9 | 1 | 2 | PC8 |
|---|
| PB8 | 3 | 4 | PC6 |
|---|
| PB9 | 5 | 6 | PC5 |
|---|
| AVDD | 7 | 8 | U5V |
|---|
| GND | 9 | 10 | NC |
|---|
| PA5 | 11 | 12 | PA12 |
|---|
| PA6 | 13 | 14 | PA11 |
|---|
| PA7 | 15 | 16 | PB12 |
|---|
| PB6 | 17 | 18 | PB11 |
|---|
| PC7 | 19 | 20 | GND |
|---|
| PA9 | 21 | 22 | PB2 |
|---|
| PA8 | 23 | 24 | PB1 |
|---|
| PB10 | 25 | 26 | PB15 |
|---|
| PB4 | 27 | 28 | PB14 |
|---|
| PB5 | 29 | 30 | PB13 |
|---|
| PB3 | 31 | 32 | AGND |
|---|
| PA10 | 33 | 34 | PC4 |
|---|
| PA2 | 35 | 36 | NC |
|---|
| PA3 | 37 | 38 | NC |
|---|
Table 11: NUCLEO-L053R8 CN10 header. |
| Column |
|---|
| | NUCLEO-L053R8 | Mote | Anchor |
|---|
| tab_mote2nucleoMap |
|---|
| tab_mote2nucleoMap |
|---|
|
|
|---|
| +3V3 | VBAT | | GND | GND | | PA9 | RX | | PA10 | TX | | GND | RX RTSn | | GND | TX CTSn |
Table 12: NUCLEO-L053R8 to mote pin mapping. |
|
Connect ST-LINK to Computer
| Anchor |
|---|
| sec_connectSTlink |
|---|
| sec_connectSTlink |
|---|
|
Connect a USB cable from your computer to the USB-mini B port labeled CN1: This is the port at the top of the NUCLEO-L053R8 (visible on the right side of Figure 7), which connects the integrated ST-LINK/V2-1 debugger to your computer, and is used to power, program and debug the board.
...