Versions Compared

Version Old Version 3 New Version 4
Changes made by

Jonathan Simon

Jonathan Simon

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Necessary Hardware

...

Necessary Hardware

  • Microcontroller/development board of your choice
    • With necessary programmer
  • SmartMesh IP Mote (DC9003A-B)
    • With 6 female-female jumper cables
  • SmartMesh IP Manager (DC2274A-A)
  • SmartMesh Interface Board (DC9006A)
    • With USB-A to USB-micro cable
  • Computer (should support Python and Java)

...

  1. Just like with the mote, identify the correct serial port name and connect to the CLI with a serial terminal of your choice (again, see Table 1 for configuration details).

  2. Unlike the mote, you will first have to login to have access to the commands we want:

    login

     

    > login user
      
  3. You now have access to a wide range of commands, where the most interesting ones are shown below.


Expand
 
titleClick here to expand the CLI commands...
Panel

  • sm: Displays information about the motes in the network. The manager itself will always be the first one listed (with MoteID 1)

    Code Block
    languagetext
    titleShow Motes
    > sm
     MAC                MoteId  State Nbrs Links Joins    Age StateTime
00-17-0D-00-00-60-39-35    1     Oper    1    21     1      0    4-05:25:14
00-17-0D-00-00-58-63-C1    2     Oper    1     9    49      4    0-00:28:39

  • trace motest on: Turns on a trace which shows mote state transitions as they connect to or drop from the network.

    Code Block
    languagetext
    titleTrace Mote States On
    > trace motest on

> 103190771 : Mote #2 State:   Lost -> Negot1
> 103192421 : Mote #2 State: Negot1 -> Negot2
> 103195937 : Mote #2 State: Negot2 ->  Conn1
> 103197989 : Mote #2 State:  Conn1 ->  Conn2
> 103202092 : Mote #2 State:  Conn2 ->   Oper

  • set config <param>=<value>: Set a configuration parameter in the Manager. This change is persistent, but only takes affect after a reboot.

    Code Block
    languagetext
    titleSet Configuration Parameter: Network ID
    > set config netid=1229

  • show config: Show the persistent configuration parameters

    Code Block
    languagetext
    titleShow Configuration
    > show config
netid = 1229
txpower = 8
frprofile = 1
maxmotes = 33
basebw = 9000
dnfr_mult = 1
numparents = 2
cca = 0
channellist = 00:00:7f:ff
autostart = 1
locmode = 0
bbmode = 0
bbsize = 1
license = 00:00:00:00:00:00:00:00:00:00:00:00:00
ip6prefix = fe:80:00:00:00:00:00:00:00:00:00:00:00:00:00:00
ip6mask = ff:ff:ff:ff:ff:ff:ff:ff:00:00:00:00:00:00:00:00
radiotest = 0
bwmult = 300
onechannel = 255

  • set acl mac=<macAddr> key=<joinKey>: Add an Access Control List entry for the given MAC address and mote specific join key. This change is persistent, but only takes affect after a reboot.

    Code Block
    languagetext
    titleAdd ACL Entry
    > set acl mac=01-23-45-67-89-AB-CD-EF key=000102030405060708090A0B0C0D0E0F
Set OK

  • show acl: Show the motes currently whitelisted on the manager Access Control List.

    Code Block
    languagetext
    titleShow ACL
    > show acl
ACL:
    MAC: 01-23-45-67-89-AB-CD-EF
----

  • delete acl <macAddress | all>: Remove all entries in the Access Control List or the one specified by the given MAC address.

    Code Block
    languagetext
    titleDelete ACL Entry
    > delete acl all
Delete all ACL records

  • reset system: Software reset (reboot) of the manager.

    Code Block
    languagetext
    titleReset Manager
    > reset system
Reset initiating. Please wait

> Disconnecting; 1
 70978 : Lost
 71702 : Lost
 72425 : Lost
 73148 : Lost
 73871 : Lost
 74594 : Lost
 75318 : Lost
SmartMesh IP Manager ver 1.2.4.1.  (x100)
   829 : **** AP connected. Network started
Info

Refer to the SmartMesh IP Embedded Manager CLI Guide for a complete list of available CLI parameters for the manager.